Zalman Z Machine LQ1000 Extreme Hybrid Liquid Cooling Enclosure, Aluminum Alloy

Z-Machine LQ1000
Extreme Hybrid Liquid Cooing Enclosure
Dimensions 480(L) x 220(W) x 450(H) mm
Weight 15kg (33lb)
Material Aluminum Alloy
Motherboard Compatibility Standard ATX / micro ATX
PSU Compatibility Standard ATX / ATX12V
PCI/AGP Card Compatibility Full Size
Drive Bays 3.5" Bay x 5, 5.25" Bay x 4
Front I/O Port USB Port x 2, IEEE1394(Firewire) Port x 1
Headphones x 1, MIC x 1
Dimensions 125(L) x 172(W) x 26(H) mm
Weight 800g
Material Aluminum Alloy, Acrylic
Coolant Capacity Max. 300cc
Power Consumption 6W, DC 12V
Maximum Flow Rate 300l/hr
Maximum Lift 1.8m
Dimensions 220(L) x 220(W) x 30(H) mm
Bearing Type 2 Ball - Bearing
Fan Speed (Min ~ Max) 550rpm ± 10% ~ 850rpm ± 10%
Dimensions 63(W) x 63(L) x 40(H) mm
Weight 160g
Material Cover (Aluminum Alloy), Base (Pure Copper)
Material Propylene Glycol & Anti-Corrosion Agent
Volume 250cc
Freezing Point -9 ℃
Replacement Cycle 1 Year
① Fan Speed Gauge
- Display the 120mm Rear Fan’s rotation speed in real-time.
② FND (Flexible Numeric Display)
- Temperature Display: Coolant Temperature (upper display), Ambient Temperature (lower display)
- Coolant Level Sensing
- If the coolant level drops below a threshold level, an alarm will sound and the display will flicker. Please refill with
- coolant, if the display flickers.
- Coolant Temperature Sensing
- If the coolant’s temperature reaches above 60°C(92 ), an alarm will sound and the FND Display will flicker. If the flickering
- is observed, please check for problems.
③ Coolant Flow Rate Gauge
- Displays the coolant’s flow rate in real time.
④ Control Knob
- Controls the Fan Speed and Coolant Flow Rate.
⑤ °C/℉(Temperature Mode) Button
- Sets the temperature display to Celsius(°C) or Fahrenheit(℉).
⑥ AUTO/MANUAL Button
- AUTO Mode: Automat fan speed and coolant flow rate.
- MANUAL Mode: Allows the user to manually adjust fan speed and coolant flow rate.
⑦ LED/RESET Button
- LED On/Off: A short press turn the displays’ LED’s On & Off.
- RESET: A long press for at least 5 seconds resets the cooling system.
Check that the product is placed properly.
Confirm that the coolant circulation path is correct as shown below.
- Enclosure
- CPU Water Block (ZM-WB5)
- Jump Cable
- Anti-Corrosion Coolant (ZM-G300)
- Funnel
- Silicone Tube (1m)
- 220mm LED Fan
- 220mm LED Fan Grill
- User’s Manual
Zalman affixes a Computer Noise Prevention System (CNPS) mark to all components used for noiseless computers.
Do not mix any contaminants with the coolant when filling. It may cause product failure or corrosion.
Check the manual when connecting cables. Incorrect connections can lead to fire resulting from short circuiting.
Check for leaks on the Water Blocks and Tubes before installation.
Preparing the necessary tools (Needle-Nose Pliers, Scissors) will ease the installation process.
Check to see if the DC cables are properly connected before use.
If the coolant is not circulating properly or if the pump’s flow rate becomes too low for other reasons, the red LED will begin to flicker with an alarm sound. Immediately turn the system OFF and contact the place of purchase.
Must use the provided coolant. Regularly check the amount of coolant and replenish as needed (replacement cycle of the ZM-G300 coolant is 1 year).
If a leak is found, turn off the system immediately and contact the place of purchase.
Do not block the Air Ducts on either side of the product. This can lead to fan failure, increased noise, or a decrease in product performance.
Make sure that the Water Pump is functioning properly.