D-link Dgs-1510-20 20-port Gigabit Smartpro Switch With 16 Utp, 2 Sfp And 2 Sfp+ 10g Ports
No Longer Available
Overview
The DGS-1510 Series is D-Link?s latest generation of SmartPro switches with 10G
port connectivity, making them ideal for deployment in SME/SMB core
environments. The DGS-1510 Series provides a reliable, scalable, and modular
interconnection between core switches and edge switches with rich capabilities
and simplified flexibility. Available in 16, 24 and 48 10/100/1000 Mbps port
models, these switches also include four optical ports ? including 2 Gigabit SFP
and 2 10G SFP+ ports. The 24 and 48 port versions are also available with 4 10G
SFP+ ports instead of the 2 Gigabit plus 2 10G configuration.
10G SFP+ Stacking/Uplink Ports
Depending on whether linear or fault-tolerant ring stacking is implemented,
users can use one or two 10-Gigabit SFP+ ports to create a physical stack. Six
units or 288 Gigabit ports can be configured as a stack using optional direct
attach cables to provide high bandwidth on the DGS-1510 Series with cost
efficiency. Users can mix from any of the DGS-1510 SmartPro series in a single
stack to allow simultaneous and easy configuration, management and
troubleshooting.
Flexibility and Scalability
The DGS-1510 Series supports virtual stacking via D-Link?s Single IP Management
(SIM), allowing up to 32 devices to be managed via a single IP. This simplifies
management of small workgroups or wiring closets while allowing the network to
be scaled to handle increased bandwidth demand. SIM reduces the number of IP
address needed in the network and allows switches to be stacked together over
Ethernet instead of using physical uplink or stacking ports. This eliminates the
need for specialized stacking cables and removes distance barriers that can
limit topology options when using other stacking technology.
Extensive Layer 2 Features
The DGS-1510 Series switches are equipped with a complete lineup of Layer 2
features including IGMP Snooping, Port Mirroring, Spanning Tree, and Link Layer
Discovery Protocol (LLDP). The IEEE 802.3x Flow Control function allows servers
to directly connect to the switch for fast, reliable data transfer. At 2000 Mbps
Full Duplex, the Gigabit ports provide high-speed data pipes to servers with
minimum data transfer loss. Network maintenance features include Loopback
Detection and Cable Diagnostics. Loopback Detection is used to detect loops
created by a specific port or VLAN and automatically shut down the affected port
or VLAN. The Cable Diagnostics feature, designed primarily for administrators
and customer service representatives, can quickly discover the type of error on
cables and determine the cable quality.
QoS, Bandwidth Control
The DGS-1510 Series supports Auto Surveillance VLAN (ASV) and Auto Voice VLAN,
which are best suited for VoIP and video surveillance deployments. Auto
Surveillance VLAN is a new, industry-leading technology built into D-Link Smart
Switches. This technology consolidates data and surveillance video transmission
through a single SmartPro switch, sparing businesses the expense of maintaining
expensive dedicated hardware and facilities. ASV also ensures the quality of
real-time video for monitoring and control without compromising the transmission
of conventional network data. The Auto Voice VLAN technology enhances VoIP
service by automatically placing voice traffic from an IP phone to an assigned
VLAN. With higher priority and an individual VLAN, these features guarantee the
quality and security of VoIP traffic. Furthermore, the DSCP markings on Ethernet
packets enable different levels of service to be assigned to network traffic. As
a result, these voice and video packets take precedence over other packets. In
addition, with Bandwidth Control, network administrators can reserve bandwidth
for important functions that require more bandwidth or might require high
priority.
Secure your Network
D-Link?s innovative Safeguard Engine protects the switches against traffic
flooding caused by virus attacks. The switches also support 802.1X port-based
authentication, allowing the network to be authenticated through external RADIUS
servers. In addition, the Access Control List (ACL) feature enhances network
security and helps to protect the internal IT network by screening ingress
traffic based on MAC or IP addresses. The DGS-1510 Series includes ARP Spoofing
Prevention, which protects from attacks on the Ethernet network that may allow
an intruder to sniff data frames, modify traffic, or bring traffic to a halt
altogether by sending fake ARP messages to the network. To prevent ARP Spoofing
attacks, the switch uses Packet Control ACLs to block invalid packets that
contain fake ARP messages. For added security, the DHCP Server Screening feature
screens rogue DHCP server packets from user ports to prevent unauthorized IP
assignment.
IPv6 Ready
The DGS-1510 Series is IPv6 ready and supports various IPv6 functions such as
MLD Snooping, IPv6 ACL/QoS, and IMPBv6 to ensure seamless integration of next
generation networks. The DGS-1510 Series also supports a IPv4/v6 dual stack
function that allows the switch to act as a bridge between IPv4 and IPv6
networks. Finally, all DGS-1510 Series are certified to be IPv6 Ready Logo Phase
2, which guarantees interoperability for IPv6 environments.
Versatile Management
The DGS-1510 Series provides a D-Link Network Assistant Utility and a web based
management interface that enables administrators to remotely control their
network down to the port level. The D-Link Network Assistant Utility allows
customers to easily discover multiple D-Link SmartPro Switches within the same
L2 network segment. With this utility, users do not need to change the IP
address of their PC. It also simplifies the initial setup of the SmartPro
Switches. Switches within the same L2 network segment that are connected to the
user?s PC are displayed on screen for instant access. This allows extensive
switch configuration and basic setup of discovered devices including password
changes and firmware upgrades. The DGS-1510 Series also supports D-View 6.0 and
a fully featured Command Line Interface (CLI) via dedicated out-of-band console
port. D-View 6.0 is a Network Management System that allows for the central
management of critical network characteristics such as availability,
reliability, resilience, and security. CLI management of the switches is
possible via console port and Telnet interfaces. This makes it possible to
adjust basic settings, passwords, configuration files, and firmware with ease.
Layer 3 Traffic Management
The DGS-1510 Series supports advanced traffic management features, including
static routing. In static routing, IP routes are manually entered into a routing
table, which allows for communication between different user groups in different
VLAN segments in a network. The switch can directly handle inter VLAN routing
using multiple interfaces, making the network run faster and more efficiently.
Because the switches can manage internal routing, the network router can be
assigned to handle external traffic routing only.
Energy Saving
DGS-1510 switches are capable of conserving power without sacrificing
operational performance or functionality by using D-Link Green 3.0 technology.
Using the 802.3az Energy Efficient Ethernet standard, the network will
automatically decrease the power usage when traffic is low with no setup
required. For environments not fully supporting the standard, DGS-1510 switches
offer advanced power-saving settings including port shutoff, LED shutoff, and
system hibernation based on custom scheduling profiles. The profiles can also be
applied to the PoE switch so that there is no unnecessary power consumption
during off hours.
Port Standards & Functions
• IEEE 802.3 10BASE-T Ethernet
• IEEE 802.3u 100BASE-TX Fast Ethernet
• IEEE 802.3ab 1000BASE-T Gigabit Ethernet
• 802.3ae 10 GbE,
• IEEE 802.3x Flow Control for Full-Duplex Mode,
• Auto-negotiation
Number of Ports
• DGS-1510-20: 16 10/100/1000 Mbps, 2 Gigabit SFP, 2 10G SFP+
• DGS-1510-28: 24 10/100/1000 Mbps, 2 Gigabit SFP, 2 10G SFP+
• DGS-1510-28P: 24 10/100/1000 Mbps PoE capable, 2 Gigabit SFP, 2 10G SFP+
• DGS-1510-28X: 24 10/100/1000 Mbps, 4 10G SFP+
• DGS-1510-52: 48 10/100/1000 Mbps, 2 Gigabit SFP, 2 10G SFP+
• DGS-1510-52X: 48 10/100/1000 Mbps, 4 10G SFP+
Network Cables
• UTP Cat. 5, Cat. 5e (100 m max.) EIA/TIA-568 100-ohm STP (100 m max.)
Full/Half Duplex
• Full/half duplex for 10/100 Mbps and Gigabit speed
Media Interface Exchange
• Auto or configurable MDI/MDIX
Performance
Switching Capacity
• DGS-1510-20: 76 Gbps
• DGS-1510-28: 92 Gbps
• DGS-1510-28P: 92 Gbps
• DGS-1510-28X: 128 Gbps
• DGS-1510-52: 140 Gbps
• DGS-1510-52X: 176 Gbps
Transmission Method
• Store-and-forward
MAC Address Table
• 16,000 entries per device
MAC Address Update
• Up to 512 static MAC entries,
• Enable/disable auto-learning of MAC addresses
Maximum 64 bytes Packet Forwarding Rate
• DGS-1510-20: 56.54 Mpps
• DGS-1510-28: 68.45 Mpps
• DGS-1510-28P: 68.45 Mpps
• DGS-1510-28X: 95.24 Mpps
• DGS-1510-52: 104.16 Mpps
• DGS-1510-52X: 130.95 Mpps
Packet Buffer Memory
• DGS-1510-20: 1.5 MB per device
• DGS-1510-28: 1.5 MB per device
• DGS-1510-28P: 1.5 MB per device
• DGS-1510-28X: 1.5 MB per device
• DGS-1510-52: 3 MB per device
• DGS-1510-52X: 3 MB per device
PoE (DGS-1510-28P only)
• PoE Standard IEEE 802.3af, 802.3at
• PoE Capable Ports Ports 1 to 24: Up to 30 W
• PoE Power Budget Max. 193 W
Physical & Environmental
AC Input
• 100 to 240 VAC 50/60 Hz internal universal power supply
Maximum Power Consumption
• DGS-1510-20: 20.3 W
• DGS-1510-28: 24 W
• DGS-1510-28P: 238.7 W (PoE on), 29 W (PoE off)
• DGS-1510-28X: 22.3 W
• DGS-1510-52: 38.4 W
• DGS-1510-52X: 44.2 W
Standby Power Consumption
• DGS-1510-20: 11.4W/100V 12.2W/240V
• DGS-1510-28: 14.6W/100V 15.2W/240V
• DGS-1510-28P: 22.7W/100V 21.0W/240V
• DGS-1510-28X: 14.6W/100V 15.2W/240V
• DGS-1510-52: 27.3W/100V 27.6W/240V
• DGS-1510-52X: 28.6W/100V 28.9W/240V
Smart Fan Quantity
• DGS-1510-20: 1
• DGS-1510-28: 1
• DGS-1510-28P: 2
• DGS-1510-28X: 1
• DGS-1510-52: 2
• DGS-1510-52X: 2
Acoustics
• DGS-1510-20: 43.8 dB(A)
• DGS-1510-28: 43.8 dB(A)
• DGS-1510-28P: 46.4 dB(A)
• DGS-1510-28X: 42.7 dB(A)
• DGS-1510-52: 44.2 dB(A)
• DGS-1510-52X: 45.8 dB(A)
Heat Dissipation
• DGS-1510-20: 41.6 BTU/hr
• DGS-1510-28: 72.3 BTU/hr
• DGS-1510-28P: 814.0 BTU/hr
• DGS-1510-28X: 76.0 BTU/hr
• DGS-1510-52: 130.9 BTU/hr
• DGS-1510-52X: 138.8 BTU/hr
Operation Temperature
• 23 to 122 ˚F (-5 to 50 ˚C)
Storage Temperature
• -4 to 158 ˚F (-20 to 70˚C)
Operation Humidity
• 0% to 95% non-condensing
Storage Humidity
• 0% to 95% non-condensing
Dimensions
• DGS-1510-20:
• 11 x 7.09 x 1.73 inches (280 x 180 x 44 mm)
• 19? standard rack mounting width, 1U height
• DGS-1510-28:
• 17.36 x 8.26 x 1.73 inches (440 x 210 x 44 mm)
• 19? standard rack mounting width, 1U height
• DGS-1510-28P:
• 17.36 x 8.26 x 1.73 inches (440 x 210 x 44 mm)
• 19? standard rack mounting width, 1U height
• DGS-1510-28X:
• 17.36 x 8.26 x 1.73 inches (440 x 210 x 44 mm)
• 19? standard rack mounting width, 1U height
• DGS-1510-52:
• 17.36 x 9.84 x 1.73 inches (440 x 250 x 44 mm)
• 19? standard rack mounting width, 1U height
• DGS-1510-52X:
• 17.36 x 9.84 x 1.73 inches (440 x 250 x 44 mm)
• 19? standard rack mounting width, 1U height
Weight
• DGS-1510-20: 2.7 lbs (1.24 kg)
• DGS-1510-28: 4.4 lbs (2.00 kg)
• DGS-1510-28P: 5.6 lbs (2.54 kg)
• DGS-1510-28X: 4.4 lbs (2.00 kg)
• DGS-1510-52: 5.3 lbs (2.40 kg)
• DGS-1510-52X: 5.3 lbs (2.40 kg)
Diagnostic LEDs
• Power/Stacking ID/Fan (per device),
• Link/Activity/Speed (per 10/100/1000 Mbps port),
• Link/Activity/Speed (per Gigabit SFP port),
• Link/Activity/Speed (per 10G SFP+ port)
Certifications
• CE, FCC, C-Tick, VCCI, BSMI, CCC
• Safety cUL, CB
Software Features
Stackability
• Virtual Stacking Support
• D-Link Single IP Management
• Up to 32 devices per virtual stack
• Physical Stacking
• Supports Duplex Chain/Ring topology
• Up to 40G stacking bandwidth full duplex
• Up to 6 units per stack
L2 Features
• MAC Address Table: 16K
• Flow Control
• 802.3x Flow Control
• HOL Blocking Prevention
• Jumbo Frame up to 9000 Bytes
• IGMP Snooping
• IGMP v1/v2 Snooping
• IGMP v3 awareness
• Supports 512 IGMP groups
• Supports 128 static multicast addresses
• IGMP per VLAN
• Supports IGMP Snooping Querier
• Host-based IGMP Snooping Fast Leave
• MLD Snooping
• Supports MLD v1/v2 awareness
• Supports 512 groups
• Supports 128 Static Multicast Addresses
• Per VLAN MLD Snooping
• Host-based MLD Fast Leave
• MLD Snooping Querier
• Spanning Tree Protocol
• 802.1D STP
• 802.1w RSTP
• 802.1s MSTP
• Loopback Detection
• 802.3ad Link Aggregation
• Max. 32 groups per device/8 ports per group
• Port Mirroring
• Support 4 mirroring groups
• One-to-One, Many-to-One
• Supports Mirroring for Tx/Rx/Both
• Multicast Filtering
• Forwards all unregistered groups
• Filters all unregistered groups
• LLDP, LLDP-MED
VLAN
• 802.1Q Tagged VLAN
• 4K VLAN Groups
• Configurable VID: 0~4094
• GVRP
• Asymmetric VLAN
• Auto Voice VLAN
• Auto Surveillance VLAN
Quality of Service (QoS)
• 802.1p Quality of Service
• Queue Handling
• Strict Priority Queue (SPQ)
• Weighted Round Robin (WRR)
• Deficit Round Robin (DRR)
• SPQ + WRR
• 8 queues per port
• Bandwidth Control
• Port-based (Ingress/Egress, min. granularity for 10/100/1000 BASE-T ports is
64 Kb/s)
• CoS based on
• 802.1p priority
• VLAN
• MAC address
• Ether type
• IP address
• DSCP
• Protocol type
• TCP/UDP port number
• DSCP of IPv6 Traffic Class
• IPv6 flow label
L3 Features
• ARP
• 256 Static ARP
• Supports Gratuitous ARP
• IPv6 Neighbor Discovery (ND)
• 8 IP Interfaces
• Default Routing
• Static Routing
• 64 IPv4 Static Route Entries
• 32 IPv6 Static Route Entries
Access Control List (ACL)
• ACL based on
• 802.1p priority
• VLAN
• MAC address
• Ether type
• IP address
• DSCP
• Protocol type
• TCP/UDP port number
• DSCP of IPv6 Traffic Class
• IPv6 flow label
• ACL Actions
• Permit
• Deny
• Max. 256 access list
• Max. 768 rules
• Single or multiple ports (each rule)
• Time-based ACL
• ACL Statistics
Security
• Port Security
• Supports up to 128 MAC addresses per port
• Broadcast/Multicast/Unicast Storm Control
• Dynamic ARP Inspection
• Static MAC
• D-Link Safeguard Engine
• DHCP Server Screening
• ARP Spoofing Prevention
• Max. 64 entries
• SSH
• Supports v2
• Supports IPv4/IPv6
• BPDU Attack Protection
• SSL
• Supports v1/v2/v3
• Supports IPv4/IPv6
• Traffic Segmentation
• IP-MAC-Port Binding
• DHCP snooping
• IP Source Guard
• Dynamic ARP inspection
• DHCPv6 Guard
• RA Guard
• IPv6 Snooping
• IPv6 Source Guard
• DoS Attack Prevention
AAA
• Compound Authentication
• 802.1X Port and MAC-based Authentication
• Supports RADIUS and Local Server
• Supports EAP, OTP, TLS, TTLS, PEAP
• Web-based Access Control (WAC)
• Port-based Access Control
• Host-based Access Control
• Dynamic VLAN Assignment
• Guest VLAN
• MAC-based Access Control (MAC)
• Port-based Access Control
• Host-based Access Control
• Dynamic VLAN Assignment
• Japan Web-based Access Control (JWAC)
• Port-based Access Control
• Host-based Access Control
• Dynamic VLAN Assignment
OAM
• Cable Diagnostics
• Factory Reset
Management
• CLI
• Telnet Server
• TFTP Client
• IPv6 Neighbor Discovery
• Configurable MDI/MDIX
• SNMP
• Supports v1, v2c, v3
• SNMP Trap
• System Log
• Max. 10,000 log entries
• DHCP Client
• D-Link Network Assistant support
• SNTP
• ICMPv6
• IPv4/v6 Dual Stack
• DHCP Auto Configuration
• RMON v1
• Debug Command
• Dual Image
• Web based GUI
D-Link Green 3.0 Technology
• Power Saving by:
• Link Status
• LED or Port Shutoff
• System Hibernation mode
• Time-based PoE (PoE model only)
Optional SFP Transceivers
• DEM-310GT 1000BASE-LX, single-mode, 10 km
• DEM-311GT 1000BASE-SX, multi-mode, 550 m
• DGS-712 1000BASE-T to SFP transceiver
Optional SFP+ Transceivers
• DEM-431XT-DD 10GBASE-SR SFP+ Transceiver (with DDM), 80m: OM1 & OM2 MMF, 300m:
OM3 MMF
• DEM-432XT-DD 10GBASE-LR SFP+ Transceiver (with DDM), 10km
• DEM-435XT-DD 10GBASE-LRM SFP+ Transceiver (with DDM), 220m
Optional SFP+ Direct Attach Stacking Cables
• DEM-CB100S 10-GbE SFP+ 1 m Direct Attach Cable
• DEM-CB300S 10-GbE SFP+ 3 m Direct Attach Cable
• DEM-CB700S 10-GbE SFP+ 7m Direct Attach Cable