• Chassis
  Barebone PC with a black plastic chassis
  Dimensions: 142 x 142 x 42 mm (LWH) = 847 ml
  Weight: 0.4 kg net, 1.2 kg gross
  Hole for Kensington Lock
  Includes vertical stand and 75 / 100 mm VESA mount
• Low Power Consumption
  Power consumption in idle mode under Windows 10: ca. 5 W
• Operation Position
  1) Horizontal
  2) Vertical with stand
  3) VESA-mounted behind an appropriate monitor
• Operation System
  This barebone system comes without operating system.
  It is compatible with:
  - Windows 10, 64-bit
  - Linux, 64-bit
• Processor
  Model: Intel Core i5-7200U (ULV)
  System-on-a-chip architecture (SoC): no chipset required
  BGA1356 package - directly soldered onto the mainboard
  Code name: Kaby Lake-U (7th Generation Intel Core)
  Cores / Threads: 2 / 4
  Clock rate: 2.5~3.1 GHz
  L1/L2/L3 Cache: 128 kB / 512 kB / 3072 kB
  Memory controller: DDR4-2133 Dual Channel (1.2 V)
  TDP wattage: 15 W maximum
  Manufacturing process: 14 nm
  Maximum Tjunction Temperature: 100 °C
  Supports Hyper-Threading (HT), 64-bit, VT-x (EPT), VT-d, Enhanced SpeedStep, NX bit, AES-NI, SSE 4.1/4.2
  Integrated graphics engine
• Cooling Fan
  Built-in CPU cooling fan with 4-pin connector
  Supports temperature-controlled RPM fan speed
• Integrated Graphics
  Intel HD graphics 620
  GPU clock frequency: 300~1000 MHz
  Execution Units (EUs): 24
  Two digital audio/video ports support two independent screens (dual monitoring):
  Supports Ultra HD / 4K resolution at 3840 x 2160 Pixels
  1) DisplayPort 1.2 [1] supports Ultra HD @ 60 Hz
  2) HDMI 1.4b supports Ultra HD @ 30 Hz
• Mainboard / BIOS
  AMI BIOS in 8 MByte EEPROM with SPI interface
  Supports resume after power failure
  Supports Wake on LAN (WOL)
  Supports Power on by RTC Alarm
  Supports booting from USB devices and SD card reader
  Supports hardware monitoring and watch dog function
  Supports Unified Extensible Firmware Interface (UEFI)
• Power Adapter
  External 65 W power adapter (fanless)
  Input: 100~240 V AC, 50/60 Hz, max. 1.6 A
  Output: 19 V DC, max. 3.42 A, max. 65 W
  DC Connector: 5.5 / 2.5 mm (outer/inner diameter)
• Memory support
  2x SO-DIMM slots with 260 pins
  Supports DDR4-2133 (PC4-17000) SDRAM at 1.2 V
  Supports Dual Channel mode
  Supports a maximum of 16 GB per DIMM, maximum total size: 32 GB
  Supports two unbuffered DIMM modules (no ECC or registered)
• 2.5" Drive Bay
  Supports one Serial ATA hard disk
  or one SATA SSD drive in 6.35 cm / 2.5" format
  Device height: 15 mm (max.)
  Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth
• Card Reader
  Integrated SD card reader
  Supports SD, SDHC and SDXC memory flash cards
  Supports booting from SD card
• M.2 Slot for SSDs
  The M.2 2280 BM slot provides the following interfaces:
  - PCI-Express Gen. 2.0 X4 with up to 32 Gbps Data Transfer Speed
  - SATA v3.0 (max. 6 Gbps)
  It supports M.2 cards with a width of 22 mm
  and a length of 42, 60 or 80 mm (type 2242, 2260, 2280).
  Supports M.2 SATA SSDs (with B+M key) and M.2 PCIe SSDs (with M key)
• Audio
  Audio Realtek® ALC 662 High-Definition Audio Codec
  3.5 mm / 4-pole combo audio connector for headphones and microphone [2]
  Digital multi-channel audio output: via HDMI and DisplayPort
• Gigabit LAN
  Ethernet Controller Intel i211
  Supports 10 / 100 / 1.000 MBit/s operation (Gigabit)
  Supports WAKE ON LAN (WOL)
  Supports network boot by Preboot eXecution Environment (PXE)
  IEEE 802.3az Energy Efficient Ethernet (EEE)
  Interface: PCIe v2.1
• Wireless LAN
  Built-in M.2-2230-A/E WLAN card and internal antenna
  Single-Chip 1T1R WLAN Controller Realtek RTL8188EE
  Supports IEEE 802.11b/g/n, max. 150 Mbps up-/downstream
  Security: WPA/WPA2(-PSK), WEP 64/128 bit, IEEE 802.11x/i
• Front Panel connectors
  USB 3.0 type A
  USB 3.0 type C
  SD card reader (supports SD, SDHC, SDXC)
  Power button
  Power LED (blue, flashing when in suspend mode)
  HDD LED (orange)
• Back Panel connectors
  DisplayPort 1.2 [1]
  HDMI 1.4b
  2x USB 2.0
  Gigabit LAN (RJ45)
  Audio Combo Port for headphones and microphone (3.5 mm jack, 4-pole) [2]
  DC-input connector for external power adapter
  2x perforation for optional external WLAN antennas
• Left Side connectors
  Serial RS232 COM port (D-Sub, 9-pin)
  Note: The serial connector (COM port) cannot be used if the NC03U5 is operated in vertical position.
• Always-On Jumper
  By removing Jumper JP1 (please refer to the Quick Installation Guide)
  the system will start unconditionally once power is applied. [4]
• Clear CMOS Jumper
  Short Jumper JP2 for about 10 seconds to restore factory settings of BIOS.
• Supplied Accessories
  Multi-language Quick Installation Guide
  Driver DVD for Windows
  VESA mount set (two parts, made of steel, with 6 screws)
  2x aluminium stand with screws for vertical operation
  Bracket for a 2.5" drive with 8 screws
  Power adapter with AC power cord
• Environmental Spec
  Operating temperature range: 0~40 °C [3]
  Relative humidity range: 10~90% (non-condensing)
• Conformity/Certifications
  EMI: CE, FCC, BSMI, RCM, R&TTE, VCCI
  Safety: CB, BSMI, ETL, CCC
  Other: RoHS, Energy Star, ErP
  This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:
  (1) 2004/108/EC relating to electromagnetic compatibility (EMC),
  (2) 2006/95/EC relating to Electrical Equipment designed for use within certain voltage limits (LVD),
  (3) 2009/125/EC relating to ecodesign requirements for energy-related products (ErP),
  (4) 1999/5/EC related to Radio and Telecommunications Terminal Equipment (R&TTE)

[1] How to convert DisplayPort into HDMI/DVI
The DisplayPort outputs can be converted to HDMI or DVI by an additional, passive adapter cable. For example:
DELOCK 82590: 1 m, DisplayPort (male, 20p) to HDMI-A (male, 19p)
DELOCK 82435: 5 m, DisplayPort (male, 20p) to DVI-D (male, 24p)
The integrated graphics automatically detects the connected display and puts out the appropriate electric signal - either DisplayPort (without an adapter) or HDMI/DVI (with an adapter).
However, a monitor with a DisplayPort connector cannot be connected to the HDMI port with a simple, passive adapter. In this case an active adapter like Delock 62496 is required.
Connecting a UHD/4K display via the present HDMI port means the refreshing rate is limited to 24 Hz. 60 Hz can only be achieved by using the DisplayPort port. Should your display have a HDMI 2.0 connector, a refreshing rate of 60 Hz can be achieved by using an active adapter such as the Club 3D CAC-1070 for example.
[2] Audio connector
The 3.5 mm audio jack at the back panel of this device supports both a 4-pole connector for headphones and microphone and headphones with only a 3-pole connector. Headsets with separate connectors for headphones and microphone, though, require an appropriate adapter, if also the microphone should be used.
[3] Caution: For high ambient temperatures over 35 °C we strongly recommend to use SSDs (supporting at least 70 °C) instead of hard disks.
[4] Power-on after Power Fail:
The BIOS setup provides a "Power-on after Power Fail" function that can be found under "Power Management Configuration". This function determines the PC's behaviour after power failure. As a matter of the nature of this function, it may fail after short power failures. This is why this PC also comes with a hardware-based solution. By removing Jumper JP1 (please refer to the Quick Installation Guide), the system will start unconditionally once power is applied.